Sơn Lót Chống Thấm Polyurethane KCC

son-chong-tham-kcc-hong

Sơn Lót Chống Thấm Polyurethane KCC Là loại sơn được cấu tạo bởi nhựa polyurethane, rất nhanh khô và có độ bám dính tuyệt vời. Sơn có khả năng thấm sâu vào bên trong xi măng, bê tông, tăng cường độ cứng cho bề mặt và tăng độ bám dính cho các lớp sơn kế tiếp .

Giới thiệu Sơn Lót Chống Thấm Polyurethane KCC

Sơn Lót Chống Thấm Polyurethane KCC

OVERVIEW

SPORTHANE PRIMER is a moisture curing polyurethane resin based coating with very quick drying.

It penetrates into substrate of cement and concretes deeply, and enhances the surface strength, and promotes the adhesion between substrate and subsequent coat.

Recommended Use

As a primer cement and concretes.

PHYSICAL PROPERTIES

  1. Finish and Color

Clear.

  1. Drying Time
Substrate temperature5℃/4120℃/6830℃/86
Set to touch30 mins10 mins5 mins
Dry through1h40 mins30 mins
Fully cured2h80 mins1h

 Sơn Lót Chống Thấm Polyurethane KCC

  1. Solids by Volume

Above 33%

  1. Spreading Rate (Theoretical)

8㎡/L in 43microns dry film thickness on a smooth surface.

  1. Specific Gravity

Approx. 1.04 (㎏/L)

  1. Flash Point

25℃/81℉ (Closed cup).

Sơn Lót Chống Thấm Polyurethane KCC

APPLICATION DETAILS

  1. Surface Preparation

Remove fins, protrusions, laitance and other impurities from the surface to be coated.

Repair the severely damaged areas with cement mortar or resin mortar. Do not apply when the temperature is less than 5℃/41℉ and relative humididty is above 80%.

  1. Application Conditions

The surfaces temperature must be above the dew point to avoid condensation.

  1. Thinning

SPORTHANE THINNER ( Thinning ratio : Max. 30% by volume )

  1. Method of Application

Brush, Roller, Spray(air or airless) application.

  1. Film Thickness

Recommended per coat 43 microns dry.

  1. Subsequent Coat

SPORTHANE WATERPROOFING BASE or SPORTHANE WATERPROOFING COAT KS CLASS 1 PTA as per specification.

  1. Recoating Interval

At 20℃: Min. : 2hours

Max. : 24hours

Remarks

If the surface is not tacky from rain and snow, it should be slightly sanding and then 30% mixied with SPORTHANE thinner. SPORTHANE PRIMER should be applied prior to application. Avoid humidity. Protect your skin and eyes, and prolonged breathing of solvent vapors. In case of contact, wash with organic solvent and followed by soap and water cleaning. Keep away from sparks and open flames. Use adequate ventilation.

Hướng Dẫn Thi Công Sơn Lót Chống Thấm Polyurethane KCC

OVERVIEW

SPORTHANE PRIMER is a moisture curing polyurethane resin based coating with very quick drying.

It penetrates into substrate of cement and concretes deeply, and enhances the surface strength, and promotes the adhesion between substrate and subsequent coat.

Recommended Use

As a primer cement and concretes.

PHYSICAL PROPERTIES

  1. Finish and Color

Clear.

  1. Drying Time
Substrate temperature5℃/4120℃/6830℃/86
Set to touch30 mins10 mins5 mins
Dry through1h40 mins30 mins
Fully cured2h80 mins1h
  1. Solids by Volume

Above 33%

  1. Spreading Rate (Theoretical)

8㎡/L in 43microns dry film thickness on a smooth surface.

  1. Specific Gravity

Approx. 1.04 (㎏/L)

  1. Flash Point

25℃/81℉ (Closed cup).

APPLICATION DETAILS

  1. Surface Preparation

Remove fins, protrusions, laitance and other impurities from the surface to be coated.

Repair the severely damaged areas with cement mortar or resin mortar. Do not apply when the temperature is less than 5℃/41℉ and relative humididty is above 80%.

  1. Application Conditions

The surfaces temperature must be above the dew point to avoid condensation.

  1. Thinning

SPORTHANE THINNER ( Thinning ratio : Max. 30% by volume )

  1. Method of Application

Brush, Roller, Spray(air or airless) application.

  1. Film Thickness

Recommended per coat 43 microns dry.

  1. Subsequent Coat

SPORTHANE WATERPROOFING BASE or SPORTHANE WATERPROOFING COAT KS CLASS 1 PTA as per specification.

  1. Recoating Interval

At 20℃: Min. : 2hours

Max. : 24hours

Remarks

If the surface is not tacky from rain and snow, it should be slightly sanding and then 30% mixied with SPORTHANE thinner. SPORTHANE PRIMER should be applied prior to application. Avoid humidity. Protect your skin and eyes, and prolonged breathing of solvent vapors. In case of contact, wash with organic solvent and followed by soap and water cleaning. Keep away from sparks and open flames. Use adequate ventilation.

Quý khách có nhu cầu về thi công sơn KCC hãy liên hệ ngay với công ty chúng tôi để nhận được sự tư vấn và sử dụng dịch vụ thi công tốt nhất cho công trình của quý khách.

Thông tin liên hệ :

  • Công ty TNHH TM DV Chí Hào
  • Địa chỉ: 606/76/4 Quốc lộ 13, phường Hiệp Bình Phước, quận Thủ Đức, TP HCM
  • Hotline: 0818.21.22.26
  • Email: [email protected]
  • Website: Thicongchongtham.org
https://thicongchongtham.org/bang-bao-gia-son-chong-tham-kcc/

Trả lời

Email của bạn sẽ không được hiển thị công khai. Các trường bắt buộc được đánh dấu *


Chat Facebook


Số điện thoại